Its too hot

Its been hot and humid for the last 3 or 4 weeks. It was so hot on the weekend that one of the HDD in the external disk enclosure stopped working. ZFS showed the disk pool in a degraded state and the LED on the side of the enclosure was off for the drive.

When I went to remove the drive I couldn't hold it as it was so hot. I left the external enclosure off for a few days. Now that its cooler I have powered it up again. All 4 drives were found and its been doing a ZFS scrub since yesterday. It should finish some time tomorrow.

The enclosure has a 80 or 90mm fan in the back but doesn't seem to move much air. I will probably have to disassemble it some time and see if I can replace the fan.

I am up to 939 plots taking up 92TB of disk space. I am computing some more plots at the moment and the estimated time to win is down to 2 months.

I am looking for a replacement motherboard and CPU for the storage server. Currently its an mATX motherboard with an i3-8100 CPU with 64GB of memory. I want one that supports more memory and PCIe lanes. I have been looking at Xeon E 2300 motherboards, however the Xeon E CPU's are limited to 128GB max memory.


Comments

Post a Comment

Popular posts from this blog

22nd of June

Image
Currently plotting away one plot at a time, using 4 threads (at least in phase 1). This is so as to not wear out the M.2 SSD so fast. I have a farmer or as Chia refers to it a "full node". I have a separate harvester machine (in a Meshify 2 case) that is basically a storage server. It has 6x WD Red 8TB drives at the moment with 60 plots taking around 5.9TiB. I have an M.2 to U.2 adapter on order, that I got on Amazon, but its not expected until next month. Must have sent it by sea.   I ordered one of these from one of my local PC shops in the hope it will turn up sooner. Its a PCIe card that you slot the U.2 drive onto it and then put the card into a PCIe x4 slot. Once this arrives I should be able to remove the M.2 SSD from the farmer and replace it with this and run multiple plots at a time. Its taking about 15 minutes to transfer a single plot from the farmer onto the harvester. I've setup a cron job to run every hour to pick up any completed plots from the local hard
Read more

More harvesting

I have 750 plots at the moment taking up 74TiB according to the the chia software. Storage server I purchased a pair of 32GB ECC memory modules to update the storage server. The machine wouldn't boot with them so I went back to using the pair of 16GB memory modules it had before. I purchased some more 16TB hard disks with a view to replacing the 8TB drives that are in the storage server. I am running ZFS and have 3 pools of drives: 5 x 16TB drives in Raidz (approx 32TB usable) 4 x 8TB drives in Raidz in an external enclosure (approx 24TB) 4 x 8TB drives (approx 24TB) The plan is to make a Raidz2 (two drive redundancy) of 10 x 16TB drives. This should yield approx 128TB usable space. The pool in the external enclosure can remain as is. I might upgrade it to larger drives at some point but don't have any plans at the moment. Due to the USB interface they are almost twice as slow as the drives inside the storage server, even though they are the same make and model 8TB drives. The
Read more

That took a while

I had to copy the plots off the 8TB disks so I could swap them out of the storage machine (aka harvester). That took 2 days, even with a 10GbE network connection between the two storage servers. I then removed the 8TB drives, put the 5 x 16TB drives in and copied the plots back. That took another 2 days with it doing 240MB/sec for most of that, which would mean the storage server simply can't write the data any quicker. After that I fired up the full node which told me 121 out of the 252 plots couldn't be opened. I ended up deleting them and I will have to plot fresh ones. Clearly they didn't survive being copied. It probably would have been quicker to upgrade the disks in the storage server and re-plot everything. At the moment I have put 4 of the 8TB drives into the external disk enclosure and I'm copying some of the remaining plots over to it. I ended up setting up a cron task to run every 10 minutes to write a small file to the disk enclosure in order to prevent the
Read more